Submersible pumps for artesian and deep wells
SX 25, 40, 70, 100, 180, 300
Multistage stainless steel submersible pump for 4 inch wells.
SXT 619, 636, 652, 668
Multistage stainless steel submersible pump for 6 inch wells.
SCM-F
Multistage submersible pump for 6 inch wells.
SP 50, 70, 100, 140, 200, 400
Multistage submersible pump for 4 inch wells.
SVM
Peripheral turbine anti-block pump for 4 inch wells.
SX 25, 40, 70, 100, 180, 300
Multistage stainless steel submersible pump for 4 inch wells.
SXT 619, 636, 652, 668
Multistage stainless steel submersible pump for 6 inch wells.
SCM-F
Multistage submersible pump for 6 inch wells.
SP 50, 70, 100, 140, 200, 400
Multistage submersible pump for 4 inch wells.
SVM
Peripheral turbine anti-block pump for 4 inch wells.
Submersible pumps for deep wells
3”SKM 100
3” (diameter 75 mm) multistage peripheral pump for deep wells. Due to its small diameter, the pump can be installed in a well with pipes with a diameter of 25 cm. Depending on the customer’s requirements, the pump can be equipped with a standard cable of 15 or 20 m with a plug.
Due to the capacitor built into the motor, the pump is ready for installation immediately after unpacking. The pump is supplied with thermal protection built into the motor winding.
4”SKM 100
4” (98 mm diameter) peripheral pumps for deep wells. The pumps are designed for wells of at least
4 inches. Durable materials such as stainless steel and brass were used in the manufacture of pump impellers. The pumps are available with the following power cables that end in a plug.
USING:
Water supply for family homes and vacation homes. Irrigation of gardens.
OLA / OLA INOX
98 mm diameter multistage deep well pumps for annular and drilled wells at least 4” diameter. The pumps have a jacket for cooling the motor so that they do not have to be completely submerged, and there is no need for a wrapped pipe, which is necessary for classic multistage pumps. Due to the capacitor built into the motor, the pump is immediately ready for installation and unpacking. The pumps are equipped with thermal protection built into the motor winding.
OLA AUTO
OLA AUTO pumps are equipped with automatic pump control, so there is no need to install additional equipment such as a pressure switch or external PC or SK control. The principle of operation of the sensor is based on flow monitoring. When the pump is connected to an electrical or hydraulic system, opening the tap will start the pump and closing it will stop the pump within seconds. The pump has a built-in non-return valve that limits the return of water from the system.
2,5″ STM
2.5” (66 mm diameter) multistage pumps for deep wells
with increased sand resistance. The 2.5 STM pumps were the first multi-stage pumps available on the Polish market with a smaller diameter
of 3″. The pump capacitor is built into the motor. The pumps are available with a cable length of 1.5 m or a 20 m basic cable terminated with a plug. Increased resistance to sand is achieved by using “floating impellers” and choosing wear-resistant materials. The pumps are equipped with thermal protection built into the motor winding.
USING:
Water supply for family homes and vacation homes. Irrigation of small gardens.
3″ Ti
3 inch (74 mm diameter) multistage deep well pump
with increased sand resistance, intended for 3 and 4 inch wells. Increased resistance to sand is achieved by using “floating impellers” and by choosing wear-resistant materials: brass, stainless steel AISI 304 and high-quality plastic materials. The pump capacitor is built into the motor, so the electrical system is much simpler than in the case of pumps with a control box. The pumps are available with a 1.5 m long cable or a 20 m long basic cable with plug. The pumps are equipped with thermal protection built into the motor winding. Due to their reliable operation and high performance, 3″Ti pumps are among the most frequently installed 3″ pumps in Poland.
USING:
Water supply for family homes and vacation homes. Irrigation of gardens.
3″ STM
Multistage pumps for deep wells with a diameter of 75 mm with increased resistance to sand, intended for wells of 3 and 4 inches. Increased resistance to sand is achieved by using “floating impellers” and choosing wear-resistant materials. The pump capacitor is built into the motor, so the electrical system is much simpler than in the case of pumps with a control box. The pumps are equipped with thermal protection built into the motor winding. The pumps are available with a 1.5 m long cable or a 20 m long basic cable with plug. The main advantage of 3STM pumps is their up to 100l/min. flow, extremely high as for 3″ pumps.
USING:
Water supply for family homes and vacation homes. Irrigation of gardens. Drainage/drainage.
3″ ISP
Multistage pumps for deep wells made of stainless steel with a diameter of 76 mm intended for wells with a minimum diameter of 4″ The maximum sand content in the water is up to 3%. Due to the materials used, ISP pumps are among the most durable pumps for deep wells. Inlet, outlet, housing, shaft and impeller are completely made of stainless steel. The pumps are supplied with 3″ oil-cooled motors.
3“ ISP series are the first pumps made entirely of stainless steel available on the Polish market. The pumps have a 2 m long power cord that can be extended.
On request, the cable can be extended to any length.
USING:
Water supply for family homes and vacation homes. Irrigation of gardens. Drainage/drainage.
3,5″ SDM
Multistage pumps for deep wells with a diameter of 90 mm
with increased sand resistance. Power supply 230 V~ /50 Hz. The IBO SDM series were the first pumps on the market that were known as “sand resistant”. Increased resistance to sand is achieved by the use of “floating impellers” and the choice of wear-resistant materials: brass, stainless steel AISI 304 and high-quality plastic materials. The pumps are equipped with thermal protection built into the motor winding. With its small diameter, the capacitor built into the motor and with a factory-mounted 20m cable, the pump is ready for installation immediately after unpacking.
The 3.5SDM pumps were the first 90 mm diameter pumps in Poland and are currently among the most frequently installed pumps by installation services.
USING:
Water supply for family homes and vacation homes. Irrigation of gardens. Drainage/drainage.
4″ SD/4″ SDM
Multistage pumps for deep wells with a diameter of 98 mm with increased resistance to sand, intended for wells with a diameter of at least 4 inches.
All SD pumps are approved by PZH (National Institute of Hygiene). 4SD/4SDM pumps are available with IBO and IBO ITALY motors as 400V~3 /50Hz and 230V / 50Hz versions. Increased resistance to sand is achieved by using “floating impellers” and choosing wear-resistant materials: brass inlet and outlet, AISI 304 stainless steel housing, shaft and filter mesh, and impellers made of high-quality plastic materials. Pumps with 230 V ~ / 50 Hz motors are equipped with a control box with a built-in capacitor and overcurrent protection. Pumps with motors from 0.75 kW to 2.2 kW are available with a cable length of 1.5 m or 20 m. The 4SD 2/12 pumps have a power cable of 20 m.
Pumps with motors from 3 kW to 4 kW are available with a 2 m long cable. Pumps with motors from 5.5 kW to 7.5 kW are available with a cable length of 3 m. On request, the cable can be extended to any length. The IBO 4SD series are the first pumps on the market that were known as “sand resistant”. Currently, they are among the few on the market that provide such high sand resistance. The maximum sand content in the water is up to 5%.
Application:
Water supply to family houses and farms from deep wells. Irrigation of gardens and orchards. Land drainage/land drainage. Water supply systems. Industrial applications.
4″ ISP/4″ ISPM
Multistage pumps for deep wells made of stainless steel with a diameter of 98 mm intended for wells with a diameter of at least 4″. The maximum sand content in water is up to 0.3%.
Due to the materials used, ISP pumps are among the most durable pumps for deep wells. Inlet, outlet, housing, shaft and impellers are completely made of stainless steel.
4 ISPM pumps with IBO and IBO ITALY 230 V ~ / 50Hz motors are available. 4 ISP pumps with IBO and IBO ITALY 400 V ~ / 50Hz motors are available.
Pumps with 230 V ~ / 50 Hz motors are equipped with a control box with a built-in capacitor and overcurrent protection.
Pumps with motors from 0.75 kW to 2.2 kW are available with a cable length of 1.5 m or 20 m. On request, the cable can be extended to any length.
Application:
Water supply to family houses and farms from deep wells. Irrigation of gardens and orchards. Land drainage/drainage. Water supply systems. Industrial applications.
IBQ HIGH SPEED DEEP WELL PUMPS
IBQ multistage centrifugal pumps for deep wells are designed for operation in drilled wells and open water reservoirs. Unlike other deep well pumps, the IBQ has advanced energy-saving motors with permanent magnets and a frequency converter. As a result, the engine reaches 6000 rpm and very high performance.
Application:
Water supply to family houses and farms from deep wells. Irrigation of gardens and orchards. Land drainage/drainage. Water supply systems. Industrial applications.
Pumps with 230 V ~ / 50 Hz motors are equipped with a control box with a built-in capacitor and overcurrent protection.
Pumps with motors from 0.75 kW to 2.2 kW are available with a cable length of 1.5 m or 20 m. On request, the cable can be extended to any length.
Application:
Water supply to family houses and farms from deep wells. Irrigation of gardens and orchards. Land drainage/drainage. Water supply systems. Industrial applications.
5″ SD
Multistage pumps for deep wells with a diameter of 127 mm with increased sand resistance, intended for at least 5″ wells. The IBO SD series were the first pumps on the market that were known as “sand resistant”. “Sand resistance” is the unquestionable advantage of IBO pumps over competing products due to their innovative and rare design with increased sand resistance, unusual for 3 inch pumps. For 5SD 25 pumps, the maximum sand content in the water is 5%. Increased resistance to sand is achieved by using “floating impellers”.
Increased resistance to sand is achieved by using “floating impellers”. If desired, a cable of any length can be installed.
USING:
Supply of large farms with water from deep water intakes, irrigation of gardens and orchards, bushes and nurseries, drainage/drainage of land. Water supply systems, industrial applications.
Pumps with 230 V ~ / 50 Hz motors are equipped with a control box with a built-in capacitor and overcurrent protection.
Pumps with motors from 0.75 kW to 2.2 kW are available with a cable length of 1.5 m or 20 m. On request, the cable can be extended to any length.
Application:
Water supply to family houses and farms from deep wells. Irrigation of gardens and orchards. Land drainage/drainage. Water supply systems. Industrial applications.
6″ SD
Multistage 146 mm deep well pumps with increased sand resistance, intended for at least 6” wells. The IBO SD series were the first pumps on the market that were known as “sand resistant”.
“Sand resistance” is the unquestionable advantage of IBO pumps over competing products due to their innovative and rare design with increased sand resistance, which is unusual for 6-inch pumps.
For 6SD 25 pumps, the maximum sand content in the water is 5%. Increased resistance to sand is achieved by using “floating impellers”. The pumps are available with 6 inch IBO or IBO ITALY motors.
If desired, a cable of any length can be installed.
USING:
Supply of large farms with water from deep water intakes, irrigation of gardens and orchards, bushes and nurseries, drainage/drainage of land. water supply systems, industrial applications.
6″ ISP
Multistage stainless steel deep well pumps up to 145mm diameter, designed to pump water with a sand content of up to 0.3% from wells of minimum 6” (150mm). The robust stainless steel construction ensures long-lasting and reliable operation.
The pumps are available with 4 and 6 inch IBO or IBO ITALY motors.
Depending on the customer’s requirements, the connected IBO ITALY motors can be cooled with oil or water.
Due to the proven design and very high parameters in relation to the diameter of the pumps, they can be used in a very wide range of applications, from water supply to large farms to industrial solutions.
USING:
Supply of large farms with water from deep water intakes, irrigation of gardens and orchards, bushes and nurseries, drainage/drainage of land. water supply systems, industrial applications.
3″/4″/6″ IBO Deep wells filled with motor oil
Multistage stainless steel deep well pumps up to 145mm diameter, designed to pump water with a sand content of up to 0.3% from wells of minimum 6” (150mm). The robust stainless steel construction ensures long-lasting and reliable operation.
The pumps are available with 4 and 6 inch IBO or IBO ITALY motors.
Depending on the customer’s requirements, the connected IBO ITALY motors can be cooled with oil or water.
Due to the proven design and very high parameters in relation to the diameter of the pumps, they can be used in a very wide range of applications, from water supply to large farms to industrial solutions.
USING:
Supply of large farms with water from deep water intakes, irrigation of gardens and orchards, bushes and nurseries, drainage/drainage of land. water supply systems, industrial applications.
